Galley Pak Shrink Wrapping Solutions
Minipack Older
PVC Film
Polyolefin Film
Used Machines
PTFE Glass Tape
Service Kits

Shopping Cart

Subtotal: £0.00
Delivery: £0.00
Total: £0.00

Select Currency
Australian DollarCanadian DollarEuroPound SterlingNew Zealand DollarUS Dollar

Your Account
Forgotten your password?



  Home > Electrical > Contactors

24 Volt Coil~ 50-60Hz Coil 3P + 1NC Contactor C-09D01A7  

24 Volt Coil~ 50-60Hz Coil 3P + 1NC Contactor C-09D01A7

Contactor 3P + 1NC 24V~ Coil

9A - AC3, 20A - AC1

VAC - 220 - 380 - 440 - 500
KW - 2.2 - 3.7 - 3.7 - 3.7
Hp - 3 - 5 - 5 - 5

Replacement Contactor For Many Applications

Minipack, Dibipack, Italdibipack, Quickpacks And many other applications & machines

See Below Information Regarding Contactors

Features of Contactors

  • A contactor is a relay that is used for switching power.
  • They usually handle very heavy loads like an electric motor, lighting and heating equipments and so on.
  • Though their output is used for switching very high loads, they are controlled by a circuit with very less power.
  • According to the loads they handle, they vary in sizes from a small device to as huge as a yard.
  • Though they are used for switching purposes, they do not interrupt a short-circuit current like a circuit breaker.
  • They have ratings ranging from a breaking current of a few amperes and 24 DC volts to thousands of amperes with many kilo volts.

Contactor – Design and Construction

Like a relay, a contactor also has

  1. Contact
  2. Spring
  3. Electromagnet

The contact part of the contactor includes the power contacts as well as the auxiliary contacts. The power contacts gains the power for the contactor and the auxiliary contacts is used to bring a loop with the rest of the rest of the devices it is attached to. These contacts are connected to the contact springs.

The contacts are controlled by the electromagnet. These electromagnets give the initial force to the contacts and make them closed. Both these contacts and electromagnet are enclosed in a frame which is usually made of insulating materials. The usually used insulating materials are Nylon 6, thermosetting plastics and so on. They are useful, as they completely insulate the contacts and help in preventing the touch of contacts. For high-end contactors, an open-frame contactor is commonly used. This will provide a greater protection from oil, dust, weather and also from explosion. The type of frame housing used may also differ according to the voltage rating used. The ones given above are restricted up to a certain voltage. If the contactors are used to manage volts higher than 1000 volts, inert gases and also vacuum is used as frame housing.

Contactors are also used in DC circuits. For their use in DC circuits, magnetic blowouts are also used. The use of blowout coils help in stretching and moving the electric arc. The electric arcs can be AC or DC. An AC arc will have can be easily extinguished as they have low current characteristics. DC arcs of the same current characteristics need more stretching need more current to be blown out. They ratings differ from about 500 Amperes to about 1500 Amperes.

Working of Contactor

As contactors are used for high-current load applications they are designed to control and reduce the arc produced when the heavy motor currents are interrupted. Other than the low current contacts, they are also setup with Normally Open contacts. These are devices which handle more than 20 Amperes current and over 100 Kilo Watts power.

The contactor has an AC/DC supply driven coil input. This will depend on the requirement. This coil will mostly be controlled by a lower voltage PLC. They can also be controlled by the motor voltage. The motor may have series of coils connected to either control the acceleration or even the resistance.

When current is passed through the contactor, the electromagnet starts to build up, producing a magnetic field. Thus the core of the contactor starts to wind up. This process helps in energizing the moving contact. Thus the moving and fixed contacts make a short circuit. Thus the current is passed through them to the next circuit. The armature coil brings in high current in the initial position. This reduces as soon as the metal core enters the coil. When the current is stopped, the coil gets de-energized and thus the contacts get open circuited.

Contactor Ratings

Ratings of a contactor are given according to the pole of the contactor. It also depends on factors like fault withstand current, coil voltage and so on. According to their rating, contactors are classified into the following.

  • AC1 – Non-inductive rows
  • AC2 – Contactors for starting of slip-ring motors
  • AC3 – Starting of squirrel-cage motors and switching off only after the motor is up to speed.
  • AC4 – Starting of squirrel-cage motors with inching and plugging duty.
  • AC11 – Auxiliary control circuits

Bookmark and Share

Our Price: £39.95
Earn 47 Points with this purchase

« Back

SALES: 07785 584474

01462 712222


Galley Pak Welcomes You

Cant't find what you need ? Try our Search box opposite. Tick Top 3 Boxes For Full Site Search

Special Offers
Video Tutorials
Sponge Rubber
Neoprene Sealing Frame Rubber 12mm x 18mm 10-Mtr Coil
Neoprene Sealing Frame Rubber 12mm x 18mm 10-Mtr Coil
Sealing Infills Beds Explained

Site Map | Terms & Conditions | Privacy & Cookies